BEFOREYOU
BEGIN
Before using this product, read the Important Safety and
Legal Information pamphlet and follow its instructions.
Take a moment before you get started to
familiarize yourself with your new
H710 Headset.
motorola
H710
Call
Button
Volume
Buttons
Multi-Color
Indicator Light
Boom
Quick Start Guide
Speaker
Microphone
(on reverse side)
(on reverse
side)
START BLUETOOTH
CHARGE
2
1
Your Headset's Battery
FEATURE
Your Phone
Charge your headset's battery for 2 hours:
Your phone's Bluetooth feature is off by default.
To use your headset, you must turn on the
Bluetooth feature in your phone.
For most Motorola phones (at the main menu):
M
Press
(Menu) > Settings > Connection >
1
Plug the Motorola charger into the end of
the headset.
1
Bluetooth Link > Setup.
Scroll to Power.
Select Change.
Scroll to On.
2
3
4
5
The indicator light turns red when the battery
is charging. It may take up to 1 minute for
the indicator light to turn on. When the
headset's battery is fully charged (about 2
hours), the indicator light turns green.
Disconnect the charger.
2
Press Select to turn on the Bluetooth
feature.The Bluetooth feature remains on
until you turn it off.
Note: Headset is not functional while charging.
Note:This product uses a lithium ion, rechargeable,
non-replaceable battery. Under normal use, the expected life
of the rechargeable battery is approximately 400 charges.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
USING A SE ECOND PHONE?
Multipoint technology allows you to make and
Use your first phone to connect to your
2
receive calls from two Bluetooth enabled
headset.
devices like your personal and business phones.
a
On your Motorola phone, press
> Settings > Connection > Bluetooth Link >
Audio Devices.
(Menu)
M
To pair a second phone to your headset, follow
these steps:
Turn off any phones or devices that are
already paired with your headset.
1
The phone lists Bluetooth devices it finds.
Select Motorola H710.
b
c
Turn off your headset by closing the headset
boom.
2
3
Select OK or Yes.
Perform Step 2 (“Start Bluetooth Feature”),
and Step 3 (”Pair”), and Step 4 (”Test and
Use”) to pair your headset with your second
phone.
Your headset is now connected to both
phones. The last paired phone (your second
phone) is now your primary phone for voice
dial functionality.
After you have successfully paired both phones
with your headset, you don't need to repeat
these steps. For daily use, ensure that your
headset is turned ON and that your phone's
Bluetooth feature is ON.
To reconnect your headset with your first phone
(and thus be connected to both phones), follow
these steps:
Turn on first phone.
1
TROUBLESHOOTING
TIPS FOR USING H710
WITHTWO PHONES
My headset will not enter pairing mode.
Make sure that any devices previously paired with the
headset are turned off. If the indicator light is flashing in blue,
first turn off the other device, then close and reopen the
headset boom.The indicator light becomes steadily lit in
blue indicating the headset is now in pairing mode.
Use the following tips when using H710's
multipoint technology:
●
Incoming calls can be answered from both
phones:
My phone doesn't find my headset.
Make sure the indicator light on your headset is on (lit in
blue) and steady when your phone is searching for devices
(see step 3).
– When answering a call, the idle phone is
disconnected from the headset.
My headset worked before but now it's not working.
Make sure your phone is on and the Bluetooth feature is
turned on in your phone (see step 2). If the Bluetooth feature
was turned off or was turned on only temporarily, you may
need to restart the Bluetooth feature (see step 2) and pair
your phone and headset again (see step 3).
– When the call ends, the idle phone is
automatically reconnected to the headset.
●
●
Last number redial dials the last outgoing call
made from either phone.
My headset will not pair with my phone.
Voice dial is accessible from either phone via
different key actions:
Open the boom flip. Press and hold both Volume buttons
and the Call button for more than 10 seconds.The indicator
light flashes blue 3 times and then become steadily lit.The
headset is now in pairing mode (see step 3B) to complete
the pairing process.
– For your primary device (last paired
phone), tap the Call button until you hear
the tone.
– For your secondary device (other paired
phone), tap the Call button and either
Volume button until you hear the tone.
Support.
If you need more help, contact us at
1-877-MOTOBLU or visit us at
TURNING HEADSET
ON AND OFF
Features and
Functions Guide
To turn your headset on, open the headset
boom.The indicator light flashes blue (if
connected with a device) or is steadilly lit (if
ready to be paired).
To turn your headset off, close the
headset boom.The indicator light will turn
off.
Multi-Color
Indicator Light
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H710.
WEARINGTHE HEADSET
Open the headset boom, then open the
earhook.
CHANGING FOR USE
ON OTHER EAR
You can wear your H710 headset on your left or
right ear.The headset comes ready for the right
ear.To change the headset for the left ear:
1
Loop the earhook over your ear.
Press the headset to your ear.
2
3
4
Open the headset boom,
then open the earhook
1
Point the headset boom towards your
mouth.
(90 from the headset).
°
2
Gently lift and pull the
top of the earhook up
and off the upper hinge
pin.Then, pull it away to
remove it.
1
Open Earhook
2
Pull Earhook
Up
3
4
Flip the headset over.
Hook the bottom of the
earhook onto the lower
hinge pin, then lift and
pull the top of the
earhook over the upper
hinge pin.
Hinge
Pin
CHANGINGVOLUME
QUICK BATTERY
CHECK
BUTTON ORIENTATION
You can also change the orientation of the
When not in a call, open the boom to check
your headset's battery charge level by
pressing and holding both Volume buttons.
volume buttons on your headset.
Close the boom to turn the headset off.
1
2
The indicator light displays charge status
until you release the buttons. See below for
details on indicator light and available talk
time based on charge status.
Press and hold down the desired
"volume up" button and open the boom.
Keep the button pressed until the
indicator light flashes blue three times.
Headset Indicator
AvailableTalkTime
Less than 2 hours
2 to 4.5 hours
Red
Volume
Buttons
Call
Button
Yellow
Green
Up to 6.5 hours
MAKING CALLS
European Union Directives
Conformance Statement
Function
Action
Hereby, Motorola declares that
this product is in compliance
with:
Make a voice dial call
(Primary phone)
Tap the Call button
and speak the
name after the tone
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
Make a voice dial call
(Secondary phone)
Tap the Call button
and either Voume
button and speak the
name after the tone
• All other relevant EU Directives.
End a call
Tap the Call button,
and hear a
high-to-low tone
Product
Approval
Number
Answer a call
Open the boom or tap
the call button (if
boom is ready open),
hear the ring tone,
then a low-to-high
tone
The above gives an example of a typical Product
Approval Number.
You can view your product’s Declaration of
Conformity (DoC) to Directive 1999/5/EC (to R&TTE
DoC, enter the product Approval Number from your
product’s label in the “Search” bar on the web site.
Reject a call
Press and hold either
Volume button until
you hear a tone
Note: Some features are phone/network dependent.
MAKING CALLS CONTINUED
AUDIOTONES
Function
Action
AudioTone
Ring tone
Short tone
Headset Status
Redial last call
Press and hold the
Call button until you
hear a tone
Incoming call
Phone network not
available
Answer a second
incoming call
Press and hold the
Call button (places
first call on hold), and
hear a tone
High to low tone
End call
Two short tones when
pressing Volume button
during a call
Volume at minimum
or maximum
Reject second incoming Press and hold either
Ascending tone
Mute enabled
Mute reminder
call
Volume button until
you hear a tone
Low tone
(repeated every
15 seconds)
Transfer a call from the
headset to the phone
Press both Volume
buttons and Call
button, and hear a
descending tone
Descending tone
Low to high tone
Mute disabled
Connection
confirmation/voice
activation
Mute or unmute a call
Tap both Volume
buttons until you hear
a mute tone
No audio indications;
deteriorating quality
Out of range
Note:Your H710 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Two tones
Low battery
repeated every minute
INDICATOR LIGHT
INDICATOR LIGHT CONTINUED
With No Charger Plugged In
With No Charger Plugged In
Headset Indicator
Headset Status
Headset Indicator
Headset Status
Off
Power off
Red flash
Idle (not connected
to phone)
Three blue flashes
Steady blue
Powering on/off
Pairing mode
Slow purple pulse
Quick red flash
Connected call muted
Quick blue/purple flashes Pairing successful
Low battery
Tip: Set your primary and secondary phones to different ring
tones to know which phone is ringing when wearing the
headset. See "Tips for using H710 withTwo Phones" for
more information.
Quick blue flash
Incoming/outgoing call
on primary phone
Slow blue pulse
Slow blue flash
Connected (on a call)
Standby (not on a call)
INDICATOR LIGHT
With the Charger Plugged In
Note: After 20 minutes on a call or of inactivity, the light stops
flashing to conserve power, but the headset remains on.
Headset Indicator
Headset Status
Note:To disable the indicator light, press and hold both
Volume buttons while turnng headset on.
Red
Battery level less
than 50% charge
Yellow
Green
Battery level more
than 50% charge
Charging complete
|